2000mj nd yag laser tattoo removal machine

Principle:

The energy of Q-switched ND:YAG laser can be absorbed by the blue and black melanin.The melanin will be fragmented so small that they can be metabolized by the lymphatic system or egested out of the body. Thus the tattoo or other pigmentations will be removed without damage to normal tissue. The treatment is safe and convenient without downtime and side effects.

Application:

The system gem-adjusting Q switch can effectively curethe mixed pigments by pigment precipitation of extraneous source withpathological pigment change of endogenous source, inclusive of erroneous darkeyebrow-embroidery, lip-embroidery, lip-soak, eye line-embroidery, lip-line,tattoo (inclusive of tattoo by extraneous wounds), pigment precipitation bysensitive source, freckle on female\'s face (male\'s), coffee spot, old agespot, black mole, and birthmark in black, blue, purple, brown, red and etc.Treatment course for different illness case as follows:

Treatments

Treatment course required ( cure times)

Treatment course interval

Remark (requirements in surgery)

eyebrow-embroidery(eyeliner grain)

1 –2 times

30-60 days

Eyebrow blow, eyeball protection

Eyebrow-embroidery ( eyeliner embroidery)

1-3 times

45-60 days

Eyebrow blow,  eyeball protection

Lip line (red dyed lip)

1-3 times

15-45 days

Use 532nm filter

Tattoo(caused by extraneous wounds)

1-4 times

30-60 days

Blood infiltration will be fine on wounds

Freckle, age spot

1-4 times

15-30 days

Blood infiltration will be fine on wounds

Birthmark, nevus/mole

3-7 times

45-90 days

Must  have  Blood infiltration .


(1)Treatmentfor tattoo in eyebrow
Customer could not open eyes during treatment, operator should adjust energyaccording to depth of tattoo color, hold the handle and move it to treatmentarea slowly to make customer feel acceptable in mentally. Right now, the speedof flash could be set 3HZ, keep head of the handle a two-finger distance totreatment area, start treatment from head of eyebrow to end of eyebrow. It isneeded to treat again in 5-10 minutes if the color of tattoo re-appear.

(2
)Remove eye line
The speed of flashes could be set 4-5HZ,adjust the energy of light to minimumenergy, keep a one-finger distance between head of handle and treatment area.Operator should strictly protect customers` eyes with panel for eyelid ormedical pledget (panel for eyelid)of 25px depth.
Treatment should be started from down eye line, customer should deeply closeeyes and keep eyeball up-sight inside. Operator should press the pledget (panelfor eyelid) with forefinger and push up eyelid, peel down eyelid with middlefinger to bare the eye line, treat it with flashes of 4-5Hz. Then, treat up eyeline. Also customer should close eyes and keep eyeball down-sight inside.Operator should press the pledget (panel for eyelid) with middle finger andpush eyelid down, push eyelid up with forefinger to bare the eye line, treat itwith flashes of 4-5Hz.

(3
)Remove lip line
The speed of flashes could be set 5Hz,keep a 3/4 finger distance between headof handle and treatment area. It is better to remove black, coffee, deep, redand brown lip line with 1064nm head at first time and then, treat again with532 nm head.
Notice: All tattoos in lip should be treated in 6 months after making. ORremoval treatment will fail. It should have 45-60 days interval to continuenext treatment until remove all.

(4
)Remove tattoo
The speed of flashes could be set 3Hz/5Hz.It is better to use high energy fortreatment until treatment area seeps a little blood. It should have 45-90 daysinterval to continue next treatment until remove all.

(5
)Remove spot and nevus
The speed of flashes could be set 3Hz/5Hz.Keep 3-4 fingers distance betweenhead of handle and treatment area. It is better to use high energy fortreatment until treatment area seeps a little blood. It is advised to use 1064nm head for normal spot and nevus treatment, but for deep color spot and nevus,it is better to use 532nm head for treatment. It should have a 15-30daysinterval to continue next treatment until remove all.

(6
)Remove birthmark
The speed of flashes could be set 3Hz/5Hz.It is better to use high energy fortreatment until treatment area seeps a little blood. It is advised to use1064nm head for birthmark treatment, but for red and deep color birthmark, itis better to use 532nm head for treatment. It should have 45-90 days intervalto continue

Laser type Sapphire Q-Switch / YAG Laser
Wave length wavelength 1064nm & 532nm &1320nm
Width of pulse 3.5-10ns
Spots Size 1-7mm
Pulse energy 20-2000mj
Pulse rate 1-10Hz
Net weight 20kg
Voltage 220V / 110V / 12A 50Hz(60Hz)
Cooling system Wind + water